Ref. S355K2 Plate > <= min max 100 470 630 100 300 450 600 Elongation Nominal Thickness (mm) Values Min (%) 40 20 40 63 19 63 150 18 150 350 17 Impact Strength (longitudinal) Nom Thickness (mm) Impact Value Min average (j) at EN10025-6 S550QL plate, S550QL High Strength Steel, S550QL - according to EN 10025-6 with minimum impact values down to -40°C (-40°F) S550QL1- according to EN 10025-6with minimum impact values down to -60°C (-76°F) Unitedsteel Mill Supply High strength steel plate, and have various stock size, if you require high strength steel plate, please contact us via Email [email protected] to contact us.
Values Min (M Pa) 16 355 40 63 325 63 80 325 80 100 315 100 150 295 Tensile strength (transverse) Nominal thickness (mm) Values (MPa) > <= min max 5 100 470 630 100 150 450 600 Elongation (transverse) Nominal thickness (mm) Values min (%, 5.65 so) > <= 5 40 20 40 63 19 63 100 18 100 150 18 Impact strength Essential Declared Performance Harmonised No. BS Section S355K2 Section S355K2 / 1.0596 according EN 10025-2 Impact Strength :Weldability :Durability : Values Min (M Pa) 16 355 40 63 325 63 80 325 80 100 315 100 150 295 Tensile strength (transverse) Nominal thickness (mm) Values (MPa) European structural steel standard EN 10025 :2004S355K2 -20 40 S355K2G3/G4 50DD E295 295 470/610 - - E295 - impact performance. This has resulted in the removal of this grade from the standard, and the lowest grade now offered is the JR version for each yield strength variation. 2 Verification of the specified impact value is only carried out when agreed at the time of the enquiry and
In the UK, the nominal values of the yield strength (f y) for structural steel, and hence the characteristic values used in design calculations, are obtained by adopting the minimum yield strength (R eH) values direct from these product standards.. S275 steel is often used on railway bridges, where stiffness rather than strength governs the design, or where fatigue is the critical design case. Ovako S355J2 S355K2 Steel, +ARASt 52, A52 FP, Q420q-D, 1501 Gr.224-460, A52 RBII, General Information:S355J2 is a structural carbon-manganese steel suitable for e.g. mechanical engineering applications. Below, a number of closely related variants are presented. 520 M is Ovako S355J2 S355K2 Steel, +ARASt 52, A52 FP, Q420q-D, 1501 Gr.224-460, A52 RBII, General Information:S355J2 is a structural carbon-manganese steel suitable for e.g. mechanical engineering applications. Below, a number of closely related variants are presented. 520 M is
1(7) S355 European Standard Steel S355 EN 10025 :2004 Standard Structural Steel Plate S355 structural steel plate is a high-strength low-alloy European S355 Structural Steel Plate, S355JR Structural Steel Plate Impact Values Charpy-V-Notch Longitudinal Average from 3 Speimens Thk. >10<150mm. 3<thk<100:315-355 S355JO Steel Plate, S355J2 Plates, S355K2 Structural Steel Plate, S355J2 + N Structural Steel Plate, IS961 High Strength Structural Steel Plates, IS 2062 E350 A High strength Structural Steel Plates, DIN St52-3U High strength Steel plates S355 steel plateS355 steel plate S355 grade steel is a medium tensile, low carbon manganese steel which is readily weldable and possesses good impact resistance (also in sub-zero temperatures).S355 High Strength Structural Steel Plates are high strength, low alloy steel plates falling under the EN 10025:2004 European standard.
Below, a number of closely related variants with various impact strength are presented. Variant SB9813 is delivered with a closely controlled C-content for predictable properties and with a CEV value of max 0.41. Variant S355J2(M) is a M-treated variant. Variant S355K2 and S355L4 both show good Impact S355K2+N - Salzgitter Flachstahl GmbHS355K2+N Non-alloy structural steels Material no. 1.0596+N Temperature Minimum notch impact energy -20 °C 27 J The samples for the tensile test are taken the product width is opposed to this. ) The tensile test values given in the table apply to longitudinal samples; in case of strip and sheet of S355K2C+N - Salzgitter Flachstahl GmbHTemperature Minimum notch impact energy-20 °C 27 J The samples for the tensile test are taken the product width is opposed to this. ) The tensile test values given in the table apply to longitudinal samples; in case of strip and sheet of widths of 600 mm they apply to transverse samlpes. 2) It applies to nominal thickness e:e < 3 mm:A80
May 11, 2012 · For minus (-) temperature without impact need to use S355J2 & S355K2 endure up to -20 degrees. Please confirm if S355JR materials will endure the cold temperature environment of -6 to -2 degrees daily all year round. If not then up to what temperature S355JR materials will have no impact. s355 plate supplier, s355j2+n plate, s355j2g3 materialImpact Values Charpy-V-Notch Longitudinal. Average from 3 Speimens Thk. >10<150mm. 3<thk<100. 315-355. 490-630. max 22. 27 Joules at -20 C. S355K2 Steel Plate, supplier of S450J0 Steel Plate, s355j2+n plate Stock Holder. Delivery Location and schedule for S355 Plate. We keep bulk stock of S355 Plate for quick delivery to our clients globally. EN 10025-2 S355K2 high strength structural steel plate JR symbol 20 temperature impact test. J0 syambol 0 temperature impact test. J2 symbol -20 temperature impact test. K2 symbol Charpy V-Notch Impact Tested Longitudinal 40 Joules at -20 C max 100mm thickness. S355K2 Characteristic. S355K2 is a low carbon, high tensile strength structural steel which can be readily welded to other weldable steel.